Irrigation Water Storage Tanks

Irrigation storage is a cost-per-cubic-metre and site-access problem. The tank may be far from a port, far from a paved road and far from a reliable power supply, so the panel system, packing and foundation have to be simple enough for a local crew. LONGCOM supplies bolted HDG, GFS, BDF and stainless tanks for agricultural irrigation, landscape water storage, livestock water and remote-site supply.

This page is for farm developers, irrigation contractors, landscape architects and rural water projects that need a practical storage tank with a predictable delivery and assembly plan. It focuses on the decisions that change the installed cost and the long-term reliability.

Typical irrigation duties

  • Farm irrigation storage and pump suction buffer.
  • Orchard, vineyard and plantation water storage.
  • Greenhouse and nursery water supply.
  • Landscape, golf-course and park irrigation.
  • Livestock watering and rural community supply.
  • Stormwater capture and reuse for irrigation.
  • Remote-site construction water and dust suppression.

System comparison

System Best fit Advantages Limitations to confirm
HDG bolted Large irrigation storage where treated steel is accepted and water is neutral. Lowest cost per cubic metre; flat-packed; fast assembly; widely used in agriculture. Corrosion at high chloride or low pH; coating touch-up; roof and liner options.
GFS bolted Long-life irrigation, aggressive water, municipal or landscape duty. Factory-fired glass coating; abrasion and corrosion resistance; long service life. Higher capital cost; panel lead time; repair procedure; foundation quality.
BDF bolted Budget-sensitive irrigation with moderate water quality. Duplex-coated galvanized panel; bolted assembly; cost between HDG and GFS. Coating warranty and water chemistry; abrasion at inlet.
Stainless bolted or welded High-value crops, brackish water, food-safety or a project specification. Corrosion resistance; no organic coating; cleanable. Higher cost; grade selection from water analysis; panel or weld cost.

What decides the irrigation tank

Input Effect What to send
Irrigation demand Sets storage volume and pump suction condition. Crop type, area, peak application rate, irrigation interval, pump curve.
Water source Determines water quality, silt load and corrosion risk. Borehole, river, canal, reservoir, recycled water; analysis if available.
Site access Determines whether panels arrive by container, truck, barge or break-bulk. Nearest port, road width, bridge limits, site access, crane or forklift availability.
Foundation Panel tanks need a level, continuous base; poor base causes leaks and panel distortion. Soil report, water table, frost depth, seismic/wind loads, existing slab.
Climate UV, wind, dust, frost and thermal movement affect coating and details. Ambient temperature range, wind speed, snow, seismic zone, exposure.
Operation Cleaning, silt removal and access affect the bottom and outlet detail. Silt load, cleaning method, drain route, access frequency.

Cost per cubic metre: what actually drives it

The cheapest tank per cubic metre is not always the cheapest installed tank. For irrigation, the installed cost includes the panels, roof, liner or coating, foundation, transport, crane, assembly labour and site supervision. A flat-packed bolted tank can reduce shipping volume, but it increases site labour. A welded tank may reduce site labour but increase transport cost and require a crane.

For large volumes, the panel count and the container plan are major cost drivers. A tank that is 1 m taller may fit the same footprint but require thicker panels and a stronger base. A tank that is 2 m wider may need more panels and a larger roof. The optimisation should be done with the site constraints, not from a catalogue volume alone.

For remote sites, the cost of a failed shipment or a missing fastener can exceed the freight saving. Pack a complete kit: panels, roof, seals, bolts, washers, touch-up material, installation drawings and a marked packing list. Send a small spare kit for seals and fasteners.

Foundation and site preparation

A bolted irrigation tank sits on a continuous base that must be level, compacted and capable of carrying the filled weight without differential settlement. A concrete ring beam or a full slab may be used depending on the tank diameter and the soil. The base should extend beyond the tank footprint and provide a clean edge for the panel.

Do not place the tank on a slope without a designed base. Do not assume a rigid tank can bridge a soft spot. The foundation design should be confirmed by a local engineer who knows the soil and the seismic/wind conditions. The tank supplier can provide loads and a base drawing, but the site engineer remains responsible for the foundation.

Installation and logistics

Irrigation sites often lack a crane or a trained crew. The assembly method should be chosen accordingly. A small tank can be assembled with a small crane and a crew; a large tank may need a planned lifting sequence, a mobile crane and a supervisor. The installer should have the erection drawing, a torque procedure and a water-fill test procedure.

Containers should be packed by erection sequence, with panels marked and small parts boxed by zone. The container loading guide shows how panel kits are arranged; the installation guide covers base acceptance, panel erection and testing. For remote sites, include a spare seal and fastener kit and a printed manual in the local language if possible.

Standards and documentation

Irrigation projects may reference a national standard, a local water authority requirement or a buyer’s specification. The structural design should follow the stated wind, seismic and snow loads. The coating or liner should be selected for the water chemistry and the site exposure. LONGCOM can provide material certificates, coating records, dimensional inspection, water-fill test records and O&M instructions. Water-quality compliance for irrigation is a project matter and should be checked against the crop and local regulations.

Irrigation FAQ

Which tank is cheapest for a farm?

HDG bolted is usually the lowest capital cost for neutral water and a site that can accept a coated tank. The installed cost also includes foundation, transport, crane and assembly. GFS or stainless may be cheaper over the life cycle where corrosion or water quality is a problem.

Can the tank be assembled without a crane?

Small tanks can sometimes be assembled with a telehandler or a small crane. Large panels are heavy and require a planned lifting method. The site should confirm the lifting equipment and the assembly crew before the container arrives.

Do I need a concrete slab?

Most bolted tanks need a level, continuous base designed for the filled weight. A concrete ring beam or full slab may be used. The foundation should be designed by a local engineer using the tank loads and the soil report.

Can the tank handle silt and dirty water?

Silt should be managed with an inlet arrangement, a settling zone and a drain. Abrasive silt can wear a coating or liner. For high silt, consider a GFS tank, a liner or a separate settling basin.

Is a roof necessary?

A roof reduces evaporation, debris and algae, and protects the water. It also adds cost and wind load. For open irrigation storage, a roof may be optional; for potable or food-related water, it is normally required.

Can you supply a tank for a remote island or desert site?

Yes, but the logistics plan is part of the design. Confirm the port, road, lifting equipment and assembly crew. Pack a complete kit with spares and a clear manual. Consider multiple smaller tanks if the site cannot handle large panels.

Related product routes

Send your irrigation demand and site plan

Need a product specification for your project?

Send your capacity, flow, water quality, material and site requirements — quotation response within 12 working hours.

Request a Quotation