Wastewater Treatment Tanks

Wastewater storage punishes the details that a clean-water tank can hide: chloride, sulfide, abrasion, sludge, odour and access for cleaning. A tank that is right for drinking water may be the wrong choice for raw sewage, trade effluent or aeration-basin duty. LONGCOM supplies bolted and welded tanks for wastewater applications in GFS, BDF, HDG and stainless, with the internal coating, roof and access arrangement matched to the duty.

This page is for municipal utilities, industrial effluent plants, environmental contractors and consultants selecting a tank for raw wastewater, equalisation, sludge, treated effluent or stormwater. It sets out the inputs that change the design and the points that should be closed before quoting.

Typical wastewater duties

  • Raw sewage receiving and wet-well storage.
  • Flow equalisation and buffering upstream of treatment.
  • Sludge holding, thickening or digestate storage.
  • Treated effluent storage and reuse.
  • Stormwater attenuation and emergency retention.
  • Industrial trade-effluent neutralisation or temporary storage.

Which tank system fits the duty?

System Best fit Why it is used Watch-outs
GFS bolted Municipal wastewater, sludge, effluent, aggressive water, large volume. Factory-fired glass coating resists corrosion and abrasion; modular panels; long service life. Coating repair procedure, foundation, panel lead time, local acceptance, roof and vent detail.
BDF bolted Industrial effluent and equalisation where a coated panel is acceptable. Duplex coating on galvanized steel; bolted assembly; cost between HDG and GFS. Chemical compatibility, coating warranty, abrasion at inlet, repair kit.
HDG bolted Stormwater, neutral water, temporary or cost-driven storage. Lower cost per cubic metre; flat-packed; fast assembly. pH, chloride, sulfide and abrasion can shorten life; coating touch-up is needed.
Stainless bolted or welded Industrial effluent with chlorides, high temperature, hygienic or high-value duty. Corrosion resistance, cleanability, repairability, no organic coating. Grade selection from water analysis; chloride and temperature limits; weld finish.

Design inputs that matter more than volume

Input Effect on the tank What to state in the enquiry
pH and chloride Selects stainless grade or coating system; drives corrosion allowance. Minimum/maximum pH, chloride mg/L, temperature, other aggressive species.
Sulfide, ammonia and organic load Affects odour, internal coating and ventilation; can accelerate degradation. Typical and peak concentrations, retention time, headspace condition.
Abrasion and solids Inlet turbulence and grit can wear coatings and panels. Solids content, particle size, inlet velocity, whether an inlet diffuser is needed.
Mixing and aeration Determines baffles, diffusers, blowers, access and roof openings. Mixing method, air rate, nozzle layout, expected foam or scum.
Odour and cover A covered tank needs venting, access and corrosion-resistant roof materials. Whether the tank must be covered, vent route, odour control, inspection access.
Sludge and cleaning Sloped or cone bottom, sump, drain and access affect cleanability. Sludge accumulation, cleaning frequency, discharge route, confined-space entry.
Structural and site Wind, seismic, snow and base bearing govern panel thickness and anchorage. Design loads, water table, soil report, height limit, access for panels.

Material and coating selection

For municipal wastewater, GFS is often the default because the glass coating tolerates a wide range of sewage and sludge conditions and can be repaired in service. BDF is used where the chemical duty is moderate and the budget sits below GFS. HDG is appropriate for stormwater or neutral effluent, but it should not be assumed to survive aggressive sulfide or chloride exposure without a review.

Stainless is selected for industrial effluent with high chloride, elevated temperature, abrasive solids or a requirement for an uncoated contact surface. SS316L is common for aggressive duty; SS304 may be adequate for neutral, low-chloride effluent. The grade should be based on the water analysis and the cleaning chemicals, not on a generic “stainless is better” statement.

The inlet is a critical detail. A high-velocity inlet can erode a coating and disturb sludge. An inlet diffuser, a stilling box or a redirected inlet may be needed. The outlet should be arranged to avoid drawing sludge or floating scum, and the tank should have a drain and access for cleaning.

Odour, ventilation and safety

A covered wastewater tank accumulates gases and can create a confined-space hazard. The roof should have a vent sized for the expected gas and air movement, and access should be arranged so that entry follows a confined-space procedure. Odour control may require a carbon filter, a biofilter or a covered headspace connection; these are normally outside the tank scope but must be coordinated.

Where mixing or aeration is used, the tank design must accommodate the equipment loads, the air distribution and the foam layer. A roof that is adequate for a quiescent tank may not be adequate for an aerated tank. State the mixing and aeration duty in the enquiry so the roof, openings and access can be designed together.

Standards and documentation

Wastewater projects may reference local environmental regulations, municipal design standards, structural codes and, for GFS tanks, ISO 28765 or an equivalent coating standard. The project should state the design basis, the required coating system, the structural loads and the inspection requirements. LONGCOM can provide material certificates, coating records, dimensional inspection, water-fill test records and O&M documentation. Environmental discharge compliance and treatment performance remain the process designer’s responsibility.

Installation and logistics

Wastewater tanks are often large, which makes the container plan and site access decisive. Panels are packed by erection sequence; roof and access components are packed separately. A large tank may require multiple containers, a flat-rack for oversize parts or a break-bulk shipment. The site must have a firm base, a level assembly area and enough room for panel handling without damaging the coating.

Coated panels should be stored off the ground, kept dry and handled with lifting equipment that does not damage the coating. Touch-up material should be available before assembly begins. The logistics hub covers container loading and packing; the installation guide covers base, panel handling and water-fill testing.

Wastewater FAQ

Can a GFS tank handle raw sewage?

GFS is widely used for municipal wastewater and sludge where the coating system and details are suitable. The actual pH, chloride, sulfide, temperature and abrasion should be reviewed. The roof, vent and access must be designed for the duty.

Is stainless better than GFS for wastewater?

Not automatically. Stainless is appropriate for high-chloride, high-temperature or abrasive industrial effluent, but it costs more and still has grade limits. GFS is often more economical for large municipal tanks. The decision should follow the water analysis and the life-cycle cost.

How do you handle odour?

The tank can be covered and vented, but odour control may need a separate filter or treatment. The vent route and access should be coordinated with the odour-control designer. A covered tank also requires a confined-space entry procedure.

Can the tank include mixing or aeration?

Yes, but the equipment loads, air distribution, foam and roof openings must be designed together. State the mixer or blower duty, nozzle layout and expected foam layer in the enquiry.

What bottom arrangement is best for sludge?

A sloped or cone bottom with a sump and drain improves cleaning and sludge removal. The outlet should avoid drawing sludge into the product stream. The cleaning method and discharge route should be decided early.

Can you supply the treatment process equipment?

The tank scope can include panels, roof, access, connections and documentation. Process equipment such as screens, blowers, mixers, filters and controls is normally supplied by the process contractor unless a wider package is agreed in writing.

Related product routes

Send your effluent analysis and duty

Need a product specification for your project?

Send your capacity, flow, water quality, material and site requirements — quotation response within 12 working hours.

Request a Quotation