Export packing for a sectional water tank has two jobs: protect the panels and put the right parts in
the right box. A panel that arrives with a bent edge or a scratched surface can slow assembly; a box
of bolts that arrives unlabelled can stop it. The packing plan should be built from the approved panel
schedule, not from a generic “sea-worthy packing” phrase in the quotation.
What is packed, and why
| Item | Packing approach | Risk if packed poorly |
|---|---|---|
| Wall / floor / roof panels | Stacked in steel-framed or braced crates; faces and edges protected; marked by ring and panel type. | Dents, bent flanges, scratched stainless, mixed rings on site. |
| Sealing strips | Rolled, labelled by width/length, bagged and kept clean; protected from sunlight and oil. | Wrong strip used, contamination, compression set, leaks. |
| Bolts, nuts, washers | Bagged by panel group or ring; quantity checked against the schedule; spare allowance stated. | Short bolts, wrong length, missing washers, assembly stop. |
| Tie rods / braces | Bundled and marked by elevation or grid; ends protected. | Mix-up during erection; structural risk if misplaced. |
| Roof beams / ladders | Long items in a dedicated rack or crate; restrained against movement. | Damage to panels; unloading hazard. |
| Connections / gaskets | Boxed separately with a packing list; gaskets kept flat and clean. | Lost small parts; wrong gasket; connection leaks. |
| Documents | Waterproof envelope in container No. 1; electronic copy sent ahead. | Customs or site reception lacks the packing list and drawings. |
Crate or bundle? The choice depends on panel size and route
There is no single “best” pack. A steel-framed crate gives rigidity and stackability but adds weight and
cost. A braced timber crate can be suitable for smaller panel groups but needs careful design for sea transport.
A bundle with edge protection and strapping can be efficient for short routes, but it offers less protection
against impact and moisture. The right choice depends on panel thickness, crate weight, container stacking and
the number of handling points between factory and site.
| Pack type | Best for | Watch-outs |
|---|---|---|
| Steel-framed crate | Export sea freight, stacked containers, heavy panel groups. | Weight, return/recycling, sharp edges, cost. |
| Braced timber crate | Smaller panel groups, routes with careful handling. | Moisture, fumigation/wood packaging rules, structural bracing. |
| Protected bundle | Short sea routes, full-container loads, low handling count. | Less impact protection; needs strong edge protection and strapping. |
If the destination country has rules for wood packaging, use compliant treated timber or a non-wood
alternative. Do not assume that a crate that works domestically will clear an export border without the right
marking.
Marking: the site should not have to guess
Every package should carry a clear, weather-resistant mark that connects it to the packing list and the
erection sequence. A practical marking set includes:
- Project / purchase order number.
- Package number and total package count (e.g. 3 of 12).
- Tank ID or bay number if more than one tank is supplied.
- Panel type: floor, wall ring 1, wall ring 2, roof, edge, corner, opening.
- Panel size and quantity in the bundle.
- Weight and lifting points for heavy crates.
- “Keep dry”, “do not stack” or “this side up” where applicable.
Use large characters and a durable label. A marker pen on a plastic wrap is not enough for a sea voyage.
Photograph the marks before loading so the site can compare the container contents with the packing list.
Moisture, cleanliness and potable duty
Stainless panels are corrosion-resistant, but they are not immune to contamination. Sea air, condensation,
dirt and oil can leave deposits that affect appearance or, in potable duty, hygiene. Keep panels dry, avoid
trapping water between sheets, and do not use oil-based protective coatings on the water-contact surface unless
the coating is approved for potable contact and can be fully removed.
Seals and gaskets should be stored away from sunlight, ozone, oil and sharp objects. Fasteners should stay in
their sealed bags until use. If the tank is for potable water, keep the packing clean and tell the site to
clean the panels before assembly according to the installation manual.
Spare parts: agree the allowance, do not improvise
A small spare allowance for fasteners, seals and gaskets is normal for an export project. The allowance
should be stated in the packing list, not hidden in the price. Panel spares are heavier and more expensive; the
need depends on the project’s handling and storage conditions. We agree the spare scope at order stage so the
site is not short and the shipment is not bloated with unnecessary panels.
Packing inspection and loading photos
| Check | What to verify | Record |
|---|---|---|
| Panel count | Matches the panel schedule; no missing or extra bundles. | Packing list with package count. |
| Panel condition | No bent edges, deep scratches, oil or contamination on water-contact faces. | Pre-packing photos. |
| Seal / fastener count | Bag quantities match the schedule; spare allowance included. | Count sheet and bag labels. |
| Crate integrity | Framing, bracing, edge protection and strapping secure. | Crate inspection photos. |
| Marks | Readable, correct and consistent with the packing list. | Photos of each mark. |
| Loading | Sequence, weight distribution and securing checked. | Loading photos and container seal number. |
These records are not bureaucracy. If a panel arrives damaged, the pre-packing and loading photos show
whether the damage happened before or during transit. If a box is short, the count sheet shows what was
packed. Good records shorten claims and keep the site moving.
Unpacking at site
Open container 1 first, check the package count against the packing list and keep the panels in their
marked groups. Do not unpack all containers at once into a single pile. Store panels on a level, clean surface
with timber bearers, protected from rain and site traffic. Keep seals and fasteners in a dry store. Recycle or
remove packing material promptly so it does not become a trip hazard or contaminate the tank interior.
